sensor

Can anyone tell me how to replace a dhw sensor on a c24 heatline boiler please

As above.... In the simpliest expansion anyone? Thanks in advance.

Went to this tap and its constantly dripping! changed the rubber washer still no joy any ideas ? ?? ?? ???? ?? ?? ???? ???? ???? ?? ??? ?? (?? ? ??) - GBP £ 62.47

Having problems with Anton v2 giving low co2 readings,just got back from calibration but was having problems before any idea,s anyone.

Just had a WB combi installed and went for their Wave controller, a feature of which is weather compensation. Enabled weather compensation during the day yesterday when the temp setting was 14C. Actual inside temp was 19C, and outside was 11C. I understand (well, perhaps that's over-stating...

vaillant 428 keeps locking out on f22 and f24 (dry fire) its in a really tall house, 6 floors (no lift, lots of stairs) boiler is in the basement with prv, 25ltr expansion vessel and filling loop. Pump, zone valves and hot water storage is on the top floor between 15 and 20 meters above...

Is it true that all food prep areas to the public that have sinks or basins will soon need sensor taps rather than long levers ?. or am i having my leg pulled..(Bit of work if so).

I'm looking for a basic 'boiler' control system - simple nv contacts will do, operating on accurate electronic (pt1000 or siimilar) probes, not ya strap on themomechanical stats. It's to control a pump based on programmable variable high/low limits on a buffer tank, working on either one or two...

Can anyone help!! where is the dhw water sensor??! have scoured the manufacturers instructions but there is no listing of it anywhere I can see!

Sent mine in for repair & service today ,, nice £185 inc , bill to pay

Thanks Irish for a constructively critical review. Just for info, the valve is available as a "flsuh only" option, without the filling valve. Ray

Why am I getting this screen pop up? Iv started outside in clean air every time and shut down in clean air?? Any ideas??

hi, sorry if this is going over old rope a bit however i have not been on for a while. anyway tonight i was sat on my pc doing my days work input when i was made aware of someone hanging around my van when i went to have a look i noticed they popped the passanger door lock out to gain...

Hello to all, Can someone please tell me if a thermistor should read the same in and of circuit? I am getting correct figures from stat with it disconnected (12k to 1k ohms)but when connected it reads zero ohms. Across the connector for sensor on pcb it reads zero.

I have a DeDietrich wall-hung boiler (model: CITY 1.24/II). The water feed comes in via a valve, pressure limiter then T-piece with pressure gauge -- showing 2bar. There is a pressure gauge on the outflow from the boiler to the rads/taps - also showing 2bar. But the boiler itself shows only...

Hi all, A browser, but new to posting. Has anyone replaced the o2 cell in their testo themselves? and where to get and how much? Cheers D.

Hi, I have a Valliant boiler which gave me 3 F22 errors in two days. The pressure gauge on the right hand side of the boiler was showing 1.5bar, so I assumed it was a faulty pump rather than it running on little water. I called BG Homecare. The repair person said that: Do all these...

lads.....just had a custurd phone me up with an f7 fault on the above boiler......in manual it says delivery sensor fault.....wtf is the delivery sensor? cheers.

Please could the heating engineers/plumbers in the trade give me an idea of how much to budget for an upgrade to the controls on my central heating system? The system is a fully pumped, open vent system controlled by a simple two channel timer (Honeywell ST699). There are no rooms stats, no...

Noticed a Burning smell from Baxi Combi 105e yesterday. On investigation found that PCB had burnt out so replaced. After resetting, red light now flashing on hot water sensor. For less than a tenner I replaced the DHW sensor but light still flashing! I've tried swapping the wires form the...