shower

Hello All, New to the forum so apologies if do any faux pas. But I have an Aqalisa Electric Quartz Shower 9.5kw (8 years old) and currently it is only giving out cold water regardless of where the temperature control is placed, the only difference is the more you move to the dial to the cold...

Hi am wondering if I can get some advice on this issue. Shower was working fine until Saturday when the dial only works when turned to cold water side and hot water side doesn't work. Other shower works fine and all taps have hot water coming out. Just wondering if get some on advice on what...

I have a Bristan recessed valve shower. It was installed 11 years ago - but hardly used as the handles are far too stiff. I have now had the cartridge replaced - but no improvement. I have been speaking to a plumber who suggested it may be as well to replace the shower [which I am prepared to...

Hi All - Apologies for what is probably a very sill question but I am trying to get a shower that attaches to my existing bath taps. I want one with an over head shower head and a hand held one but they all seem to come with thermostatic taps that involve drilling into the wall to plumb in. I...

Hi Just moved into a house and in process of renewing sealant around the shower cubicle. Feel free to skip to the bottom to get the question! There’s a gap (20mm in length & 3mm height) at the bottom of the frame (where it meets the shower tray) closest to the wall that appears to have been...

Hi, I am putting in a Rain Shower and I am quite tall. 192 cms. My concern is the rain shower is not height enough. I estimate the the distance between the top of the rain shower is going to be 12 cms and the top of my head. Is that enough? I want to get some guidance on what is the correct...

Hi Everyone, I'm moving to a megaflow from a regular immersion heater set up. The house has several showers and at the moment they are fed by gravity feeds from the immersion (hot water) and a top floor tank (cold water). All the showers are powered by (pressure drop) pumps which are fed by...

Good Afternoon. Just wondering if it would be fine to connect an electric shower to the balanced cold supply from an unvented cylinder. Replacing an old Bath mixer tap with the shower hose built into it. Regards

Hi, Just looking for some advice as seen a few different things online. I'm installing a shower tray in our bathroom but this one has a square inlay to it first. Is this just a standard wet room square plate and then a normal shower trap underneath? I have seen some mcalpine ones but they are...

For about a year, my shower on a third floor is giving an on off gas smell sometimes after a shower and particularly in the morning not long after the sun rises enough to hit our roof. I usually run some water into my p-trap and the smell goes away after a few minutes. There is a tub right...

For about a year, my shower on a third floor is giving an on off gas smell sometimes after a shower and particularly in the morning not long after the sun rises enough to hit our roof. I usually run some water into my p-trap and the smell goes away after a few minutes. There is a tub right...

Hi Everyone, Can anyone help? I have been searching but with no luck. I am trying to fit a Duravit shower trap which has a 50mm outside diameter euro pipe size outlet. I need to attach it to a 40mm UK size waste pipe and would prefer to solvent weld it as the pipe will be under a tiled...

I have bought a shower tray and it has an extra large hole for the waste trap. Its a cooke and lewis think its an eclips 1400 x 900 tray. The hole is 160mm and has a lip around it for the cap at 200mm. Cant seem to find one in the correct size, hope someone can help.

I currently have an 8.5kw electric shower on a gravity fed system in bathroom which doesn't give great flow when hot turned up but to get a 10mm cable to fuse board would be really difficult at best (I've checked and on 6mm at the minute) I would like a mains shower however changing to unvented...

Hi everyone , got a problem with a cartridge change on a mira shower. It seems only the hot side is working. The temp control only lessens the spray. Put the cartridge in the opposite way and only getting cold Im stumped.

Hi everyone, I am looking to see if anyone has purchased a bar shower where the hot is incoming from the right and cold coming from the left, really struggling to find a bar shower and riser kit to accommodate this, any advice be much appreciated thanks

I have a traditional style bath tap with shower attachment via a diverter. The lever no longer moves, and so I managed to unscrew the lever arm and the brass (colonial) piece, exposing the plastic diverter valve. Unfortunately, I am stumped as to how to get access to the diverter valve, as the...

Can you stick shower panelling straight on to plasterboard if I prime say with sbr bond

Why is my hot water tank making some sort of irritating whistling noise after I take a shower?