Just removed this shower tray.
What type of shower tray is this?
Why aren't all shower trays constructed like this?
It must weight less than 10kg and with the flat base, must be a doddle to set in place.
Hi.
We want to replace our shower tray. I've been doing lots of research trying to establish which trays are best. The current tray, I think is one of the really lightweight ones, is it acrylic? I like the idea of replacing with another acrylic, because it's lightweight and im guessing easy to...
Hi. I have have purchased 3 Mermaid wall panels to replace the tiles in our shower. These panels are 3mm in thickness. After removing the existing wall tiles, I have discovered that there is a gap around the entire shower tray, in some places the gap is greater than 3mm, the thickness of the...
Our shower room has been replaced and finished last week. The shower is an 1800 tray with the drain at the front. On using the shower we are finding a puddle at the back right which is never going to drain as it appears the tray slopes backwards when checking the edges with a spirit level.
This...
New shower tray and waste recently installed and thankfully have a cut out in ceiling below from when I was checking it's initial seal, when I spotted yday foam (from shampoo/shower gel) escaping from underneath the shower tray, out the sides of the waste.
I never really liked the initial seal...
Hi there,
I bought this 1500mm X 800mm X 30mm grey slate shower tray.
https://www.sonasbathrooms.com/en/slate-1500-x-800-shower-tray-black-with-free-shower-waste.html
It will be installed on a raised bed of 2.5 inch concrete blocks, and I might put a sheet of 18mm Marine Plywood on top of...
I’ve got to take out an old acrylic 600mm wide bath and replace it with either a similar sized one or a shower. Has anyone any source of either a bath that’s up to 600mm wide and under 1700mm long or a shower tray that’s 600mm wide and 1000-1500mm long. Really struggling to find anything...
Hi all
I'm looking for options for a 1300 x 760 shower tray - I've found a few but just wondering if anyone knows of any others out there. Ones I've found so far
- MX Elements. Available all over the internet
- Eastbrook Volente
- E:thos, from a company call bathroom-place/bathco, which have...
So I'm looking to replace my current shower tray as it has cracked. It is one of those long rectangular low profile trays as the ceiling is sloped so not too much height to work with & is in a downstairs bathroom & I believe it is a concrete base. I'm just looking for some advice as to any...
I’m about to install a stone resin shower tray, the tray (RAK Feeling) comes with a warning not to use cement for setting on and instead recommends silicone or PU foam. A few questions;
Has anyone fitting this or a similar tray with PU foam? Or is best to use silicone? Which PU foam or silicone…...
Hey there,
I purchased a black slate shower tray from a supplier. The supplier recommended that we cut it down to our required size. Is this good practice/possible? Some plumbers I speak to say absolutely not to. Others seem OK with the idea.
I hope to cut it down to around 1600x700. Cutting...
I have just received a resin capped shower tray and as best as I can tell, one corner at the back (i.e furthest away from the trap), is 3mm lower than the other corners. To be clear, this is across the top of the tray over which the tiles will be situated, although 35 mm of the edge will still...
The shower tray needs to fit in a three-sided recess that is 900 x 760 in size - see attached picture. It seems logical to place the waste at the front for access (where the rubber seal is), but the thing that slightly concerns me is whether it is a bad idea do you have it on the same side as...
I am just about to invest in a Merlyn MStone tray and need it to go on a riser kit. I already have a good quality kit for a Just Trays tray (same size / style) though and wonder if i will be able to use it?Don’t fancy spending another £90 on a kit if I can avoid it, when they were all fairly...
I am really struggling with how to do the waste pipework from a shower tray and would appreciate any advice on the best approach to take.
The tray will be sitting in a three sided recess which really complicates things. A further complication is that the soil pipe is very close by and so there...
Due to the cramped space that I have for installing a shower tray and the required positioning of the trap to be at the front left, I am severely limited on my options. I would really have preferred an Anti-Slip Shower Tray, but struggling to find one that meets my requirements.
There are very...
Hi guys,
Fully ripped out an old bathroom and installing a new one.
Getting mixed messages from Plumber and my father who is a Joiner/Carpenter
Plumber wants to fit shower tray before the walls are plastered.
Father thinks that the walls should be plastered first, he has left enough clearance...
To make fitting of the trap pipework simpler, I’m considering turning the rectangular tray around such that the trap would be positioned behind the user i.e. the water would flow away from the shower. Is there any reason why I can’t do this / it’s unadvisable?
I was wondering if a shower tray that has a upstand on all four sides would allow a semi enclosure. The shower tray will be sat against two walls but I am just confused to how the two shower panels will fit against the walls with the upstand being all the way around?
Any help would be really...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.