fill valve

I've seen a number of similar threads related to my problem...so it may be a known common issue...anyway, after a year of perfect use, the fill valve (WDI B3300-M-) in my cistern is no longer fully stopping the water inlet when the float lifts...the valve appears to work and the inlet water is...

anyone know the make of this fill valve please. all boxed and tiled in you know what its like! replacement best option:yesnod:

FREE samples | SIAMP

Just replaced the fill valve in toilet, the old one seemed to be completely broken and was not cutting off water supply when cistern full. The new one works but when the cistern is full and it cuts off the water supply it makes a large 'honking' noise for want of a better description, noise...

I have a problem with my WDI fill valve (1 year old) which suddenly misbehaved. Now every time after I flush the toilet, the tank will fill up normally but the water will run into the overflow tube for 1 or 2 minutes before it finally stops. I don't know what should I do with this, as the...

Can anyone help with how to adjust float on a Flomasta Bottom Inlet Brass Shank Fill Valve as there is no screw. its from screwfix. its been overflowing. many thanks.

Changing the fill valve on this tomorrow night, anyone familiar with the wc? Looks like the pan may have to come out to change fill valve or am i mistaken?

Hi Please forgive if this question is too simple After flushing the loo takes ages to refill water. It says online I should change the filled valve/shank valve. The upper cistern is exposed and sits on the toilet pan but the lower pan have both sides concealed and walls down either side...

I have installed a new toilet today and the water feed is gravity fed. It's a low level toilet (not that this is relevant but hey) There is lots of pressure at the water inlet isolating valve but the water 'trickles' into the cistern. I have adjusted height etc and also removed the inline...

I have fitted quite a few side and bottom entry toilets but this is my first rear entry type. I am trying to fit a rear entry filler valve to a noken compact cistern, it has a gerberit filler with brass thread but there is no nut or anything to fit the valve to something. there are no holes...

Hi chaps, I'm trying to locate these side entry 3/8 fill valves they like torbeck but special size as space is restricted. these are fitted in 40 new build flats I have to maintain. My alternative is to re-drill holes in the side of these concealed plastic cisterns and re-route 1/2 inch side...

Hello everyone! I'm in desperate need of the above SVO 4667 fill valve kit. Luck would turn out that the 5 yr old flat I moved into has a ridiculously awkward non-standard kit! Can anyone let me know where the best place is to get a new one? Many thanks.

Hi there, plumbing newbie here. I'm trying to replace a malfunctioning fill valve, and I've hit a bit of a problem, and wanted some thoughts from the experts here as to how to proceed. I've replaced the old valve assembly with a Fluidmaster 747UK side entry fill valve. The old valve assembly...

Hi, the fill valve on my saniflow toilet needs replacing but I, m not sure if I can get the part as the system is quite old using the old ballcock method. Also the overflow pipe is external going under the floorboardsvto outside rather than going back into the toilet. The overflow also has a...

First time I have seen one of these. Cannot really work it out ad it is rustef no end. Had not worked for 25yrs apparently

Wondered if somebody can help me please. I have a close coupled toilet with a Fluidmaster 400 Filling valve (came with the flushvalve (part of the pro pack i think). Anyway the valve has worked fine until I removed some tiles and managed to block the filter up, I have removed the red cap as...

Hey I have a toilet fill valve that is missing the white plastic bit at the top that redirects the water from spraying straight upwards, instead in to the bottom of the cistern can these be bought seperatly?

Hey I have a toilet cistern that is missing the white plastic bit at the top that redirects the water from spraying straight upwards but in to the bottom of thr cistern can these be bought seperatly?

Hey I'm quite new to the plumbing world (clearly!) and I only had a moment where I could look at a mates fill valve for him but when it's filling its only finley spraying out and obviously takes ages to fill, took the diaphragm out and looked all well, took it out a few times and got it to run...

Hi all, I have a rather unique problem that I'm hoping someone could help me with? I have built my own rain water haversting system to use to flush the toilet. I've used a side entry equilibrium float valve for the mains fill in my toilet cistern with sufficient air gap and weir overflow for...